search
banner

4 points should be paid special attention to the ball bearing pillow block during use!

948 Published by Jun 26,2018

The following points should be paid special attention to the ball bearing pillow block during use:

(1) The use of bearing cooling systems. The correct use of the cooling water of the ball bearing pillow block not only prolongs the service life of the ball bearing pillow block but also increases the production efficiency. The material of the ball bearing pillow block is generally made of a special bearing seat steel which is manufactured through various processes. Even the best ball bearing pillow block steel also has the limit of their use, such as temperature. Bearings in use, if the mold temperature is too high, it is easy to make the surface of the mold core early cracks, and some housings have not even more than 2000 mold cracks appear on a large area. Even in the production of the bearing seat in the production because the ball bearing pillow block temperature is too high, the mold core has changed color, and even more than four hundred degrees after measurement, such temperature encounters the chilling state of the mold release agent, and it is prone to cracking. The products are also easily deformed, strained, and die-bonded. With the use of cooling water in the ball bearing pillow block, the use of release agents can be greatly reduced, so that operators do not use release agents to reduce the temperature of the ball bearing pillow block. The advantage is that the life of the bearing seat is effectively prolonged, the die-casting cycle is saved, the product quality is improved, the occurrence of sticking, pulling and sticking of the aluminum is reduced, and the use of the release agent is reduced. It also reduces head and core losses due to overheating of the ball bearing pillow block.

ball bearing pillow block-1
(2) The ball bearing pillow block must be preheated during the start of production to prevent the sudden encounter of hot molten metal in the cold ball bearing pillow block and lead to the occurrence of turtle cracks. The more complex ball bearing pillow block can be used with torches, liquefaction Gas, good conditions with the mold temperature machine, a relatively simple bearing seat can use slow injection preheat.

ball bearing pillow block-2
(3) The cleaning of the parting surface of the ball bearing pillow block is very troublesome and it is very easy to overlook. The operator thoroughly applies kerosene to thoroughly clean the parting surface of the ball bearing pillow block, which not only prevents the bearing seat from being damaged. Moreover, after cleaning, the exhaust groove of the ball bearing pillow block blocked by the residue of the release agent or other dirt can be opened to facilitate the discharge of gas in the cavity during the injection process and improve the product quality.

ball bearing pillow block-3
(4) If the ball bearing pillow block is equipped with neutron control, attention must be paid to the fact that the signal line between the die casting machine and the ball bearing pillow block is absolutely prohibited. The reason is very clear. In daily production, it is difficult to avoid water on the signal line, or The place where the connector is wrapped is easy to break, resulting in a short circuit with the machine tool. If the signal error is caused, the alarm will automatically stop and delay the time, otherwise the signal will be disordered and the bearing seat top will be damaged. Cause unnecessary losses. Travel switch attention waterproof.

We can ball bearing pillow block and other specifications of bearings, if you are interested in our bearings, please contact me, we will do the best for you!

Contact: Miya
Email: [email protected]
Skype: [email protected]
MP/Whatsapp: +8618363031398
Wechat:18363031398

How to install the double row angular contact ball bearing?

Double row angular contact ball bearing installation is more complex than deep groove ball bearin...

Do you like ? 4,790

Read more

The cause of micro miniature bearing failure and the solution to overheating of temperature.

Failure reason of micro miniature bearing About 40% of the failure of micro miniature bearings i...

Do you like ? 1,684

Read more

Six Mistakes in the Replacement of skate shoes ceramic bearing by Novices

Novice Mistakes 1: Do not consider the characteristics of your own actions, blindly choose Althou...

Do you like ? 1,609

Read more

CNC machine bearings common quality problems and main causes.

When assembling cnc machine bearings, the Venus machine tool must be preloaded, so that the origi...

Do you like ? 2,221

Read more

the performance and feature of stainless steel self-aligning ball bearing

Performance characteristics of stainless steel self-aligning ball bearing Self-aligning ball bear...

Do you like ? 1,694

Read more

How to choose the suitable longboard skateboard wheels?

The long board has a strong sense of operation and is quick to get started. The longboard is a mu...

Do you like ? 1,587

Read more

What’s the design and installation of tapered thrust bearing?

The tapered thrust bearing with cage is a split design so that the two washers as well as the rol...

Do you like ? 1,981

Read more

the disassembly, installation and operating environment of tapered needle bearing

Disassembly of the tapered needle bearing: When the bearing is to be used continuously after it i...

Do you like ? 1,437

Read more